Just How to Set up a Tub
Just How to Set up a Tub
Blog Article
How do you feel about Installing A Bathtub?
Setting up a bath tub isn't precisely rocket science, however it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably tough task. If the old tub is conveniently accessible, the job can move immediately; if you have to open up a wall to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you install a brand-new bath tub in your restroom if you have actually currently bought a new tub as well as do not need to change the plan of your previous water pipes.
Your tools as well as product checklist ought to make up the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, activate the faucets to drain any water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least when as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in location between the faucet and the sink. Protect the tap in position with the supplier given backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The former type should be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very fascinated with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am assuming you enjoyed the entire blog post. Sharing is nice. Helping people is fun. Many thanks for your time spent reading it.
Call Us Today
Report this page